Functional safety technical resource
What Does Fail-Safe Mean in Functional Safety?
Fail-safe describes a system property in which a defined failure causes the system to enter, or allows it to remain in, a specified safe state. In functional safety, the claim is hazard- and failure-specific: fail-safe does not mean that every conceivable fault is harmless, that every valve must fail closed, or that de-energize-to-trip is always the correct design.
Technical resource from Mangan Safety Instrumented Systems (Mangan SIS)
Fail-Safe Begins with a Defined Safe State
The safe state is the process condition the SIF is intended to achieve or maintain for a particular hazardous event. That state can differ by scenario, operating mode, and equipment boundary. A valve may need to close for loss-of-feed protection and open for relief or cooling service; a pump may need to stop in one scenario and continue in another. Calling a device fail-safe without naming the hazard, required state, and relevant loss of power, signal, utility, or internal fault leaves the claim incomplete.
Fail-Safe Versus De-Energize-to-Trip
De-energize-to-trip is a design approach in which removing energy initiates the protective action. It often supports fail-safe behavior for loss of electrical power or signal, but the terms are not synonyms. Some functions require energization, stored energy, or an active sequence to reach the safe state. De-energized designs can also create spurious trips or remain vulnerable to mechanical sticking, blocked flow, loss of motive force, or failures that the selected energy state does not address.
Evaluating the Complete Failure Path
A fail-safe review should follow the complete path from sensing through logic, communications, power and utilities, output interfaces, actuator, and process response. Identify which failures are revealed, which cause a trip, which leave the function unavailable, and which can create a hazardous output. Consider common-cause events and failure combinations rather than evaluating each component in isolation. Hardware fault tolerance and diagnostics can manage some faults, but they are different concepts from the fail-safe response to a specified failure.
Specifying and Testing Fail-Safe Behavior
The SRS should state the safe state, trip action, energization philosophy, final-element position, response time, reset behavior, utility-loss response, alarm or diagnostic response, and assumptions for each SIF. Cause-and-effect documentation and application logic should implement the same behavior. Validation and proof testing should challenge credible failure and degraded conditions where practicable, not only demonstrate a normal commanded trip. Mangan SIS recommends documenting exceptions explicitly when the preferred failure position conflicts across hazards.
Mangan SIS project context
Apply Fail-Safe to documented SIS decisions
For a process SIF, fail-safe design may influence transmitter signal handling, logic-solver input and output behavior, solenoid energization, actuator spring action, utility storage, valve position, alarms, and restart permissives. Each choice should trace to the hazard-specific safe state and be verified as part of the installed function rather than inherited from a generic convention.
Sources and scope
Use the source type that fits the decision
Standards
IEC 60050 dependability terminology describes fail-safe as a system property associated with reaching or remaining in a safe state after specified failure conditions. IEC 61511-1:2016 establishes process-sector requirements for SIS to achieve or maintain a safe state of the process.
Guidance
IEC 61511-2 and the ISA-84 series provide application guidance across the SIS lifecycle. Guidance should be applied to the defined SIF and hazard; it does not establish one universally correct valve position or energization philosophy for every process.
Regulation
OSHA 29 CFR 1910.119 does not create a universal fail-safe design rule for every SIS. For covered processes, relevant PSM duties can include process safety information, PHA, operating procedures, mechanical integrity, pre-startup review, and management of change. Separate OSHA standards may contain equipment-specific fail-safe provisions outside this glossary definition.
Mangan recommendation
Mangan SIS recommends replacing generic fail-safe labels with testable, SIF-specific requirements that name the hazard, safe state, failure conditions, energy and utility response, final-element action, diagnostics, and reset behavior.
Primary references
- IEC Electropedia IEV 192-10-06 (IEC terminology)
- IEC 61511-1:2016 publication record (Process-sector standard)
- ISA-84 Series of Standards (U.S. standards series)
- OSHA 29 CFR 1910.119 – Process Safety Management (U.S. regulation)
Common questions
Clarifying Fail-Safe
Does fail-safe always mean de-energize-to-trip?
No. De-energize-to-trip often produces the desired response to loss of electrical power or signal, but some hazards require an energized action, stored energy, or an active sequence. The correct design follows the specified safe state and credible failure modes.
Should a fail-safe valve always fail closed?
No. The required failure position can be closed, open, in place, or another controlled condition depending on the process hazard and utilities. The position should be derived from the scenario and documented in the SRS and associated design records.
Can a system be fail-safe for every possible failure?
A defensible claim should identify the failures and boundary it covers. Some faults may be tolerated, detected for repair, or remain dangerous until proof testing. Combined, common-cause, mechanical, utility, and systematic failures must be evaluated separately.
Need failure behavior defined clearly?
Translate the hazard-specific safe state into testable sensor, logic, utility, and final-element requirements.
Downloadable term reference
Download: Fail-Safe – Functional Safety Glossary PDF
Save or share this term-specific reference, including the answer-first definition, engineering review considerations, and primary-source references.